Hoshizaki Low-Profile Modular Crescent Cuber MRH Uživatelský manuál Strana 12
- Strana / 40
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
12
II. Installation and Operating Instructions
WARNING
• The appliance must be installed in accordance with applicable national, state, and
local codes and regulations.
• Failure to install, operate, and maintain the appliance in accordance with this
manual will adversely affect safety, performance, component life, and warranty
coverage and may result in costly water damage.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after installation. Make sure that none have fallen into the
dispenser unit/ice storage bin.
A. Location
NOTICE
• The icemaker is not intended for outdoor use. Normal operating ambient
temperature must be within 45°F to 100°F (7°C to 38°C); Normal operating
water temperature must be within 45°F to 90°F (7°C to 32°C). Operation of the
icemaker, for extended periods, outside of these normal temperature ranges may
affect icemaker performance.
• The icemaker will not work at sub-freezing temperatures. To prevent damage
to the water supply line, drain the icemaker if the air temperature is going to go
below 32°F (0°C). See "IV. Preparing the Icemaker for Periods of Non-Use."
• The icemaker should not be located next to ovens, grills, or other high heat producing
equipment.
• Allow 6" (15 cm) clearance at rear, sides, and top for proper air circulation and ease of
maintenance and/or service should they be required.
• The location should provide a rm and level foundation for the appliance.
B. Checks Before Installation
• Visually inspect the exterior of the shipping container and immediately report any
damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. If any are left in the appliance,
it will not work properly.
• See the nameplate on the rear panel, and check that your voltage supplied corresponds
with the voltage specied on the nameplate.
• Remove the panels to prevent damage when installing the appliance. See "II.C. How to
Remove Panels."
• Remove the package containing the accessories.
• Remove the protective plastic lm from the panels. If the appliance is exposed to the
sun or to heat, remove the lm after the appliance cools.
- Hoshizaki 1
- CONTENTS 3
- IMPORTANT 3
- Important Safety Information 4
- WARNING, continued 5
- I. Specications 6
- 3. KML-451M_H 7
- 4. KML-631M_H 7
- B. Dimensions/Connections 8
- WARNING 12
- A. Location 12
- B. Checks Before Installation 12
- C. How to Remove Panels 13
- See Fig. 1 13
- D. Setup 14
- Intentionally Left Blank 15
- E. Electrical Connection 16
- WARNING 17
- See Figs. 4 through 8 18
- Air-Cooled and Remote Models 19
- Water-Cooled Models 20
- Fig. 11 25
- H. Final Checklist 31
- I. Startup 32
- III. Maintenance 33
- A. Maintenance Schedule 33
- V. Disposal 39
- HOSHIZAKI AMERICA, INC 40
Související produkty a manuály pro Stroj na výrobu ledu Hoshizaki Low-Profile Modular Crescent Cuber MRH
(84 stránky)Sealey SEKC100 manuals
Owner’s manuals and user’s guides for Equipment Sealey SEKC100.
We providing 1 pdf manuals Sealey SEKC100 for download free by document types: User Manual
Komentáře k této Příručce